My Gas Oven Not Heating Up But Burners Work?
If both your gas oven and gas burners stop working, the problem is most likely related to the gas lines and requires professional repair. If your oven has just been repaired or replaced, it’s also possible that the gas valve on the gas supply line isn’t working. You may have checked your oven thermostat and igniter and they are working fine, the problem may just be a bad connection or wiring.
If the temperature sensor is not an obvious problem, check that the oven pilot valve and heating elements are functioning properly. The reason why the oven is not reaching the correct temperature could be the temperature sensor, heating element or gas burner. An oven that does not heat is usually caused by a faulty igniter (gas oven) or heating element (electric oven). The cause could be a faulty temperature sensor or contact with the oven wall temperature sensor.
Both gas and electric ovens are equipped with a temperature sensor – a thin tube a few centimeters long that sits at the top of the oven’s rear wall. The purpose of a temperature control thermostat is to control the temperature inside a gas oven and then start firing when the oven gets too cold. The electronic control panel activates the oven safety valve on gas hob and the bake/bake element on electric hob.
Ovens without a sensor use a heat-sensitive light bulb to control the temperature of the oven. You can also insert an oven-safe thermometer during preheating to check if the temperatures match. To determine if your oven is baking at the correct temperature, all you need to do is purchase a basic temperature sensor that can handle oven temperatures.
If the thermometer consistently reads a lower temperature, such as 25 degrees, with every test, your oven may be cooking at a lower temperature than indicated. If you notice food taking longer to cook than it should or coming out of the oven undercooked, your oven may not have reached the correct temperature. There may be times when your oven is working fine, except that it doesn’t heat up to the right temperature every time. To solve this problem, you can calibrate your oven temperature to meet your expectations regarding temperature settings and cooking times.
In the event that the electric oven is not working and the hob is still working, the situation is very similar to that of a conventional gas stove. If you find that the oven won’t turn on, the first thing to determine is if the oven is malfunctioning or the switch may have tripped. To test the igniter, turn off the gas oven switch, then make sure the power is off, making sure the oven lights, clock, and any other electrical functions are not working.
If the igniter looks normal, you can turn the power back on, set the oven to heat, and watch the igniter at the start of the heat cycle. Then the control unit turns off the voltage supply to the igniter or spark, and then the gas supply to the burner. Remove the gas igniter – to do this, you just need to unscrew a couple of screws, after which the gas igniter should come out.
A dirty or defective igniter may be visible in the oven, or you may need to remove the bottom panel of the oven to gain access to it. If that doesn’t solve the problem, the igniter needs to be replaced and that is definitely a job for a qualified technician. If the igniter is not the problem, the oven’s main valve may need to be replaced or checked for faulty wiring, loose electrical connections, or faulty relays. If this is the case, you can check the piping and replace it yourself, and if your gas oven igniter is faulty, replace it by following the troubleshooting steps above.
After a few clicks, if the igniter is defective, you may smell natural gas as it comes out, at which point you should turn off the oven and contact an appliance repair company. All this time, after turning on the oven, you must monitor whether the igniter or spark starts to glow or not.
During normal operation, the indicator light will illuminate and glow bright orange when the oven controls are in cooking mode. When turned on, the stove’s igniter will begin to glow, eventually igniting the gas passing through the valve. When the igniter passes a certain amount of current through the oven safety valve, the valve opens and allows gas to flow into the oven burner.
If the oven is plugged into a wall outlet, try plugging another appliance into it to make sure there is no problem with power from the wall outlet. Before disassembling the oven and replacing parts, make sure that the oven is receiving power and that there is sufficient voltage at the outlet. If the switch is OK, check if the outlet is working – you can test the gas oven by plugging it into a separate outlet to make sure. This doesn’t happen often, but if the gas igniter is working, your best bet may be to simply replace the temperature control thermostat and see if that fixes the problem.
To schedule oven repair in Edmond Ok contact Edmond Appliance Repair by calling 405-531-0055. Or you can visit our website at https://edmondappliancerepair.net Call now!
